Hi guys, Having a nightmare problem with my 1.4 TSI. Replaced the timing chain, tensioner, head reconditioned, new valves ect, but for the 3rd time the exhaust camshaft stretch bolt has slackened off. Anyone have any idea why this keeps happening? I torque the new stretch bolts to 40nm plus 90...

Barn stored for last 20 or so years. Ran fine when put into storage but bolt from flywheel bolt got loose and has not be repaired. Body is in good shape and little rust. Was going to restore for daughter but never got to it. I found an old pic of it before going into storage. CLOSING...

I have got a 1981 Caddy with 1.6l diesel. I thought I had a blown head gasket but it turn out to be a corner was broke off on the rear bolt. I bought another used engine and got my butt burner, low compression, around 290 psi. Ok my question is on the engine with low compression can I put the...

I am wondering where the torque converter bolt access hole is so i can replace this engine. the manual i have said there is a rubber cap covering the hole and the only cap i can find is metal cap and i cant seem to remove it. i cant get the bolt through the starter hole because its on the...

Hi everyone, I have some 17's out of a 2008 beetle, bolt pattern is different can we swap the rotors to a beetle ones? What other options do i have to instal these wheels on my 2008 Rabbit?:confused::confused::confused::confused: Help grandly appreciate it. Regards

Was looking into getting a set (4) of winter tires for my GFs car (2011 Tiguan SEL) and wanted to know if these would be ok? Yokohama iceGUARD IG52c winter mobdro.bio/ luckypatcher.tips/ www.kodi.bio/ tires on rims. Tires are 225/45R-17, Rims are 5-112 bolt pattern. Any help would be greatly...

I have a front sway bar for my 81caddy but want to make sure I install it correctly. Does any one have any photos or information on installation? Is there a hole missing in my control arms for it to bolt on. Again any information would be greatly appreciated. Thankyou.

I pick up my brand new 2018 GTI Autobahn on Friday, my first GTI, I’m so excited. But I want to get winter tires for them, and am looking for recommendations. Can I drop to a smaller wheel with a bigger profile winter tire, as long as the bolt pattern is still 5x112? Need to keep costs down...

Hello everyone,, So, one of my GTI presents this year is a Torque Solution VW MQB (circle style) dogbone insert. The insert did not come with a new inro.in/watch-movies-online/ inro.in/cyberghost/ inro.in/expressvpn/ bolt; Ithought a new bolt would be required. I do need a new bolt to install...

Need help. This sommer right front fender was replaced on my Tiguan 2012, much much later when my problems were exposed, may not be related. This fall again , snow tire season. My tire shop found right front wheel lock solid frozen could not install snow tires. Asked if I had recently any...

I tried to change the oil the other day, and it isn't obvious where the oil drain plug is. Can somebody take a picture or explain exactly where the oil drain plug is? Also, is it a normal hexigon bolt or is it something special.

Getting ready to install engine in 1981 Caddy 1.6l. Which motor mount do you bolt first?

I have a 78 rabbit that I just sand blasted and did body work to. I'm on the painting stage as of right now, I also extended the rear tire fenders by about an inch. Any suggestions for what rims I should put on that are 16X8 in the front and 16X10 in the back for a 4X100 bolt pattern? Thank you...

Have just received the right tank from Just Kampers but after spraying with paint and attaching pipes etc just noticed some bolt holes are missing. I don't want to send it back.Any ideas

My aaz motor leaks at the valve cover. I have changed the gasket 3 times but am able to stop the leak. This is a center bolt valve cover that I suspect is somehow bent slightly. What have others done to solve this problem.

The bolt right below the #146 is the bolt that leaks fuel out of it. The only way to get to it to me is to take off one of the pulleys thats attacked to the timing belt and then take off another bracket to get to it. I didnt know if i was looking at it wrong and if there was another way to get...

Afternoon! I have a question related to by 1980 Rabbit 1.5 Diesel. I've done some research but still having difficulty determining if the bolts (stretch bolts?) that secure the valve cover need to be replaced after taking off the cover (circled below in red). I believe at least 1 is stripped...

Rebuilt my 1.7L and put the engine in the car before installing the headers. Upon trying to install the headers, they seem to be positioned such that they are contacting the steering rack bracket. I thought perhaps an engine alignment would remedy this but its still touching. I am thinking that...

See the thread Limited time offer. http://forums.vwvortex.com/showthread.php?9061834-Local-Atlanta-Area-Only-Limited-time-offer-Must-be-Picked-up 89 Wolfsburg rear white leather seats both lower and upper . Front Passenger side fender Front Clipper Bumper skin, and rebar. Send me a pm.