Search Results for ‘nut’

Hi. Could anyone tell me how many teeth anti theft lock nut key is needed for the mk5 golf rims? Sent from my iPhone using Tapatalk

My LLW Alternator that I replaced just had a semi-failure. The Case screws that hold the body together had a strippage from the re-builder. One of the Case screws backed out due to strippage and started to hit the Alternator fan. A 4.5mm Nut wasn't replaced on the screw on the back, so I added 3...

Brand knew to Moding... just bought first set of rims...Velox... want to but red lugnuts... how do I find out what to look for when buying...where do I get the OEM size? Anyone? Sent from my SM-N950U using Tapatalk

Trying to change the left side boot. I'm not having much luck installing it over the rack flange or the rubber ring. I'd there some trick to this installation without removing the entire r & p?

Hey guys, Recently found out my right taillight has been accumulating water since I purchased it about a month ago. I've seen posts about using a hair dryer to remove the moisture, but I have got enough water in my taillight to swim in. I found out that only a nut for one of the 2 bolts...

Read more about the 9 Things You Should Always Have in Your Car.

I have pulled my driver side axle to replace it. I ordered a rebuilt one, twice and neither have fit. Both of them bind when you tighten the axle nut fully. I can back off half a turn and have no problems. When I compare the old axle with the rebuilt there is a difference in the way the ends...

Hi, I'm new. I would like to carry out a full nut & bolt, bare metal restoration of an old Beetle and then enter the car in shows. I understand there are Show & Shine and Concours d'Elegance events but that the processes and finish of my vehicle will be critical as to which type of event I...

Hi! The bolt that holds the door check strap in place fell off and now the door swings wide open. What do I need to do to screw it back in place? I'm gonna get a new bolt and nut from the dealer but I'd like to avoid paying hundreds of dollars to get the work done. I don't know how to reach...

Need to know what size socket I need to remove axle nut on my 2001 beetle and does it need to be 12 point or will a 6 point work:confused:

My brother and I are going to be doing a little bit of work on my 2012 Jetta SE 2.5 next weekend and I'm having issues finding the factory torque specs for ALL parts of the suspension. As a matter of fact, I haven't found any torque specs for any nut, lug, or bolt on the car. Can anyone help me out?

Greeting from Guernsey in the Channel Islands everyone! Not sure if it's in the right section but here's a pic of my vdubs.

Seems likely, heres what up. The bolt that goes out of he little boot and in through the wheel bearing housing with a bolt on the end spins with the nut...but the joint seems tight and moves well. seems like a bad a things but am i missing something?

rr

New on here so thought i would throw a picture or so up FULL strip down, not a nut or bolt untouched :o took me 18 months all in all and while we were there did a FULL color change over to A75 BMW Melbourne red as found on the 2013 M3 :cool: Has been on the road a few weeks now and am quite...

I changed out my driverside bearing and accidentally stripped out the tie rod end nut, so to get it off I used a cutting wheel. My problem is that I believe that it is a one piece tie rod but not sure, there is no back off nut and no place to put a wrench on any of it. After looking around all...

What size is the upper nylon strut nut on a 1992 cabriolet?

Is there some sort of trick to remove the strut insert nut? Mine will not budge.

I took out my distributor (yes, all the way out), but to do so I loosened the 10mm nut facing out, not the one that's tough to get to behind the distributor base. It fits back in nicely, but how do I know whether or not the cam is spun right to fit back into the base? Something must be wrong...

I need torque specs for the rear nut that hold the drums on. ie. the bearings are behind the nut and I do not want to over torque. Thanks for the help